replacement transmitter

Identity Owner's Manual

Click Here  
"Personal Identifier" (PI)  Click Here to Order

How to replace the battery in your Identifier

Sold in Dealerships Aftermarket Dept., the "Personal Identifier" is the key that unlocks

the magic of the Identity system. Once programmed and placed on your customer's

key ring, the "Personal Identifier" will become the "Invisible Watch Dog" of their vehicle.

With NO buttons to push, NO extra keys to insert, NO additional effort whatsoever,

Identity will arm and disarm quietly and effectively every time you use your vehicle.

Each Identity system can be programmed with up to 6 "Personal Identifiers"

per vehicle. One for every member of the family.
 
"Wireless PIN device"

 

What if I lose my keys?

This customer version of the "Wireless PIN" can be kept in the vehicle for just such emergencies. This version has a 4 digit PIN security as well as custom programming options. This allows it to be used as an additional daily use transmitter.

The Wireless PIN may be used as a touch Key Pad for our customers wishing not to carry a transmitter with them. If a wrong code is entered 3 times, it locks out for 5 minutes.
 

Setting the WPD to the 1,2,3,4 mode from "One touch"

Step 1: Press the button with two dots. (The function button)

Step 2: Enter the 2-digit code of 1 and 1, and press the function button.

            (The Red LED will flash once)

Setting customer WPD to "One touch" transmit from 1,2,3,4 mode

Step 1: Enter the 4-digit access code. 1,2,3,4.

           (The LED will green)

Step 2: Press the function button.

            (The LED will stop flashing)

Step 3: Enter the 2-digit code of 1 and 1 slowly, followed by the function button.

            (The LED will flash twice)

Note:  Pressing the send button will immediately transmit the disarm code to the vehicle, and the LED will illuminate green. The disarm code will be transmitted as long as you depress the send button, for up to 6 seconds

Setting the Wireless Pin from 1,2,3,4 code to customer's choice

Step 1: Enter 1-2-3-4 into the "Wireless PIN Device"

           (The LED will begin blinking Green)

Step 2: Press the second function button with the 2 dots

            (The LED will stop blinking)

Step 3: Enter 1-1 into the "Wireless PIN Device"

            (The LED will remain off)

Step 4: Press the second function button again

            (The LED will blink once)

Step 1: Enter 1-2-3-4 on the "Wireless PIN Device"

            (The LED will begin blinking Green)

Step 2: Press the second function button with the 2 dots

            (The LED will stop blinking)

Step 3: Enter your new PIN code

            (The LED will turn a solid Green)

Step 4: Press the second function button with the 2 dots, again

            (The LED will shut off)

Step 5: Re-enter your new PIN code

            (The LED will blink green rapidly, confirming code)

 

Changing your PIN Code on your "Wireless PIN Device" with existing PIN

Step 1: Enter your existing PIN code on the "Wireless PIN Device"

            (The LED will begin blinking Green)

Step 2: Press the second function button with the 2 dots

            (The LED will stop blinking)

Step 3: Enter your new PIN code

            (The LED will turn a solid Green)

Step 4: Press the second function button with the 2 dots, again

            (The LED will shut off)

Step 5: Re-enter your new PIN code

            (The LED will blink green rapidly, confirming code)

 

Changing your "Personal Identifier's" Mode (Between Automatic and Manuel)

To go to Manual mode:


Step 1: Hold down the button on the face of the "Personal Identifier" or "PI", until the light goes out

Step 2: Then press the button again 3 times.

           -It will then blink 3 times.

Step 3: When the light finishes blinking, press it 3 times, once more.

You are now set to "Manual" mode. Your "PI" will only transmit when the button is pressed.

 

To go to Automatic mode:

Step 1: Hold down the button on the face of the "PI", until the light goes out

Step 2: Then press the button again 3 times.

           -It will then blink 5 times.

Step 3: When the light finishes blinking, press it 3 times, once more.

You are now set to "Automatic" mode. Your "PI" will only transmit when movement is detected.